 |
Woodworking Online
|
| View previous topic :: View next topic |
| Author |
Message |
Zed Rafi
Guest
|
 Posted: Wed Oct 27, 2004 6:02 pm Post subject: Wood sticks on my benchtop |
 |
|
Hello,
A couple of years ago, i bought a workbench assembly at Canadian Tire (our
Home Depot).
The top working surface has a number of holes bored through it, in each of
which can be fitted the lower end of a cross-sectionally rectangular,
elongated wood stick. When this wood stick is fitted in one of these bores,
it projects vertically upwardly from the surface of the workbench.
What are these for??? I imagine they're used as guiding means of some sort.
I've kindda discarded them cause i didn't see any use for them.... but i've
seen them around on other workbenches than mine, so i imagine they must be
useful to some extent.
thanks for the info |
|
| Back to top |
|
 |
Stephen M
Guest
|
| Posted: Wed Oct 27, 2004 6:39 pm Post subject: Re: Wood sticks on my benchtop |
|
|
They are called "dog holes". The stick that you place in them is called a
"bench dog"
There should be a vise which also has one or more dog holes. A dog placed in
a fixed hole in the bench top used in conjuction with a dog in the vise
become the "jaws" of potentially large vise or clamp above the surfadec of
the bench.
You should be able to get the idea from the picture on this link
http://www.woodirect.com/workbench.htm
"Zed Rafi" <zed@poloniese.com> wrote in message
news:KSNfd.11295$Qs6.1128072@news20.bellglobal.com...
| Quote: |
Hello,
A couple of years ago, i bought a workbench assembly at Canadian Tire (our
Home Depot).
The top working surface has a number of holes bored through it, in each of
which can be fitted the lower end of a cross-sectionally rectangular,
elongated wood stick. When this wood stick is fitted in one of these
bores,
it projects vertically upwardly from the surface of the workbench.
What are these for??? I imagine they're used as guiding means of some
sort.
I've kindda discarded them cause i didn't see any use for them.... but
i've
seen them around on other workbenches than mine, so i imagine they must be
useful to some extent.
thanks for the info
|
|
|
| Back to top |
|
|
Joe_Stein
Guest
|
| Posted: Wed Oct 27, 2004 6:43 pm Post subject: Re: Wood sticks on my benchtop |
|
|
benchdogs
Zed Rafi wrote:
| Quote: |
Hello,
A couple of years ago, i bought a workbench assembly at Canadian Tire (our
Home Depot).
The top working surface has a number of holes bored through it, in each of
which can be fitted the lower end of a cross-sectionally rectangular,
elongated wood stick. When this wood stick is fitted in one of these bores,
it projects vertically upwardly from the surface of the workbench.
What are these for??? I imagine they're used as guiding means of some sort.
I've kindda discarded them cause i didn't see any use for them.... but i've
seen them around on other workbenches than mine, so i imagine they must be
useful to some extent.
thanks for the info
|
|
|
| Back to top |
|
|
Stephen M
Guest
|
| Posted: Wed Oct 27, 2004 6:48 pm Post subject: Re: Wood sticks on my benchtop |
|
|
| Quote: |
seen them around on other workbenches than mine, so i imagine they must
be
useful to some extent.
|
BTW they are *very* useful in holding a workpiece when doing hand work such
as planing. |
|
| Back to top |
|
|
Zed Rafi
Guest
|
| Posted: Wed Oct 27, 2004 7:44 pm Post subject: Re: Wood sticks on my benchtop |
|
|
Ahhhhhh...... i see.....
now that you've told me that, i see a million uses for it.... to think that
i've been clamping my workpieces down on my workbench all this time.... it
was annoying me so much and i kept thinking "there's gotta be another
way...."
thanks a lot for the info
"Stephen M" <smeier-spamless@primelink1.net> a écrit dans le message de
news:cloc1o0256r@news4.newsguy.com...
| Quote: |
They are called "dog holes". The stick that you place in them is called a
"bench dog"
There should be a vise which also has one or more dog holes. A dog placed
in
a fixed hole in the bench top used in conjuction with a dog in the vise
become the "jaws" of potentially large vise or clamp above the surfadec
of
the bench.
You should be able to get the idea from the picture on this link
http://www.woodirect.com/workbench.htm
"Zed Rafi" <zed@poloniese.com> wrote in message
news:KSNfd.11295$Qs6.1128072@news20.bellglobal.com...
Hello,
A couple of years ago, i bought a workbench assembly at Canadian Tire
(our
Home Depot).
The top working surface has a number of holes bored through it, in each
of
which can be fitted the lower end of a cross-sectionally rectangular,
elongated wood stick. When this wood stick is fitted in one of these
bores,
it projects vertically upwardly from the surface of the workbench.
What are these for??? I imagine they're used as guiding means of some
sort.
I've kindda discarded them cause i didn't see any use for them.... but
i've
seen them around on other workbenches than mine, so i imagine they must
be
useful to some extent.
thanks for the info
|
|
|
| Back to top |
|
|
patrick conroy
Guest
|
| Posted: Wed Oct 27, 2004 8:03 pm Post subject: Re: Wood sticks on my benchtop |
|
|
On Wed, 27 Oct 2004 10:02:10 -0400, "Zed Rafi" <zed@poloniese.com>
wrote:
| Quote: |
Hello,
elongated wood stick. When this wood stick is fitted in one of these bores,
it projects vertically upwardly from the surface of the workbench.
|
They're called Bench Dogs. Often metal (brass, iron) - some round,
some square.
They're stops that you butt your one end of workpiece against. The
other end is butted up against the vise. Tighten the vise and you
pinch the piece firmly 'tween the dog and the vise. |
|
| Back to top |
|
|
AAvK
Guest
|
| Posted: Wed Oct 27, 2004 8:10 pm Post subject: Re: Wood sticks on my benchtop |
|
|
| Quote: |
They are called "dog holes". The stick that you place in them is called a
"bench dog"
There should be a vise which also has one or more dog holes. A dog placed in
a fixed hole in the bench top used in conjuction with a dog in the vise
become the "jaws" of potentially large vise or clamp above the surfadec of
the bench.
You should be able to get the idea from the picture on this link
http://www.woodirect.com/workbench.htm
Off topic: |
Stephen do you own this bench? It shows that the center wood top is 1 1/8" thick,
that should be 5/4 or 6/4 stock I think, but do you think it matters if the wood is
that thin? It seems to be a good deal compared to the Rockler $400 Sjoberg.
On topic:
I just bought 8 Lignum Vitae pen blanks to become bench dogs, they'll be fun to make!
Alex |
|
| Back to top |
|
|
AAvK
Guest
|
| Posted: Wed Oct 27, 2004 8:20 pm Post subject: Re: Wood sticks on my benchtop |
|
|
| Quote: |
Ahhhhhh...... i see.....
now that you've told me that, i see a million uses for it.... to think that
i've been clamping my workpieces down on my workbench all this time.... it
was annoying me so much and i kept thinking "there's gotta be another
way...."
thanks a lot for the info
That's what happened to me when I got it... "snap" ... "I get it" ... "I get ALL of it!" |
Alex |
|
| Back to top |
|
|
Stephen M
Guest
|
| Posted: Wed Oct 27, 2004 9:34 pm Post subject: Re: Wood sticks on my benchtop |
|
|
| Quote: |
Stephen do you own this bench?
|
No. That was just the first picture I could find with a quick search.
My bench is home made.
| Quote: |
It shows that the center wood top is 1 1/8" thick,
that should be 5/4 or 6/4 stock I think, but do you think it matters if
the wood is
that thin?
|
In the field of the bench, no, I don't think super thick is required. But
more beef is always better.
| Quote: |
It seems to be a good deal compared to the Rockler $400 Sjoberg.
|
The materials for my bench (including vise wardware) were less than that,
and it weighs well over 200 lbs.
I'm really a proponent of "build your own". It doesn't mater if you
implement a plywood, tubafor, or a classic european hardwood bench. Just do
it. It's good skill-building excercize for almost anybody.
A complete newbie doesn't need that need the classic bench and probably will
opt for a simpler design. By the time you *need* the classic bench, you'll
have the skills to pull it off.
There are no one right answer in bench building. It varies with the skills
and techniques of the user/builder.
| Quote: |
On topic:
I just bought 8 Lignum Vitae pen blanks to become bench dogs, they'll be
fun to make!
Alex
|
|
|
| Back to top |
|
|
Phisherman
Guest
|
| Posted: Thu Oct 28, 2004 2:02 am Post subject: Re: Wood sticks on my benchtop |
|
|
On Wed, 27 Oct 2004 10:02:10 -0400, "Zed Rafi" <zed@poloniese.com>
wrote:
| Quote: |
Hello,
A couple of years ago, i bought a workbench assembly at Canadian Tire (our
Home Depot).
The top working surface has a number of holes bored through it, in each of
which can be fitted the lower end of a cross-sectionally rectangular,
elongated wood stick. When this wood stick is fitted in one of these bores,
it projects vertically upwardly from the surface of the workbench.
What are these for??? I imagine they're used as guiding means of some sort.
I've kindda discarded them cause i didn't see any use for them.... but i've
seen them around on other workbenches than mine, so i imagine they must be
useful to some extent.
thanks for the info
|
I use a dog when I am sanding a panel, especially with a belt sander.
It keeps the material in place. Sometimes a dog and a dog in the vise
are used to hold material. Once you understand how they work, you'll
probably use them more often. (You can't have too many clamps.) |
|
| Back to top |
|
|
AAvK
Guest
|
| Posted: Thu Oct 28, 2004 4:08 am Post subject: Re: Wood sticks on my benchtop |
|
|
I was much pondering everything, prices, models, reviewing people's
personally made benches all over the 'net, picking up ideas and so forth. My
Grandmother gave me her old maple breakfast table top for the exact purpose
of a woodworking bench, very sweet of her. But I saw that link and thought
it might be easier than building one, perfect size too. Then I read that they are
not producing anything as changes are being made. Then I called them, the
owner answered, I asked some questions on "what is going on", he told me
the company has been sold to [?] in Colorado, they will start producing and
benches should be available by the end of this year.
It is a real structure of a quality hard maple that can't be found as common
like in the days it was new. Layers of wood and under-side boards and a leaf.
You could go into "Levitt's" or "Wick's" and buy it at a common price back
then.
My then uncle swiped the legs for maple guitar neck when he was learning to
be a luthier (now at Fender). It had no more use as the space was taken by a
newly installed kitchen island.
The maple is 5/4? (exactly 1" thick) so I have the idea of ripping the table top
sections into 2" wide boards to be used as standing lamination upon 2x2 DF
planed flat to create about a 3" thick top.
Say the 2x2 are length-wise T&G is 60" or 62" x 20" wide for depth as a base
for a cross-wise laminated maple standing, not T&G... does that sound good
or should I try and put it into a better perspective? Say you are facing the front
of the bench, the maple board laminates are traveling from you to the back
of the bench while glued on top of the T&G 2x2's which travel left and right.
Just my idea. I think it would be a strong enough top. I have the trestle designed
in my head, almost. Sorry for the grueling long reply.
Thanks for the great reply and encouragement, I appreciate it much!
Alex |
|
| Back to top |
|
|
Stephen M
Guest
|
| Posted: Thu Oct 28, 2004 5:11 pm Post subject: Re: Wood sticks on my benchtop |
|
|
| Quote: |
I was much pondering everything, prices, models, reviewing people's
personally made benches all over the 'net, picking up ideas and so forth.
My
Grandmother gave me her old maple breakfast table top for the exact
purpose
of a woodworking bench, very sweet of her.
|
That sound Very cool to me. I like the idea of recycleing family furniture
| Quote: |
It is a real structure of a quality hard maple that can't be found as
common
like in the days it was new. Layers of wood and under-side boards and a
leaf.
You could go into "Levitt's" or "Wick's" and buy it at a common price back
then.
My then uncle swiped the legs for maple guitar neck when he was learning
to
be a luthier (now at Fender). It had no more use as the space was taken by
a
newly installed kitchen island.
|
I worthy cause.
| Quote: |
The maple is 5/4? (exactly 1" thick) so I have the idea of ripping the
table top
sections into 2" wide boards to be used as standing lamination upon 2x2 DF
planed flat to create about a 3" thick top.
|
DF = Doug Fir? Idunno'bout that. If I follow correctly, you would have 1"
"veneer" of maple over 2" of DF. That sounds like you are asking for a big
cup as the expansion and contraction rates differ.
| Quote: |
Say the 2x2 are length-wise T&G is 60" or 62" x 20" wide for depth as a
base
for a cross-wise laminated maple standing, not T&G... does that sound good
or should I try and put it into a better perspective?
|
90 degrees to the DF Like plywood on steroids? - Terrible idea  . The
seasonal movement will split it it.
| Quote: |
Say you are facing the front
of the bench, the maple board laminates are traveling from you to the back
of the bench while glued on top of the T&G 2x2's which travel left and
right.
Just my idea. I think it would be a strong enough top. I have the trestle
designed
in my head, almost. Sorry for the grueling long reply.
|
Here's what I would (and to some degree did):
1 - invest in Landis' "The Workbench Book", about $20 and really fun read.
2- Most of the beating, pounding and stress that wou will put on a bench for
hand work is within 6-8 inches of the front edge. Build up the beef in the
front where you need it.
3- Suppplement you stock with more maple. I purchased "brown maple". It's
maple, but with some heartwood. Same stuff, not as pretty, half the price.
4 - Keep all the wood going left to right. If you do want bread-board ends
(going front to back) you can only lock the end at one point and let the
rest of the joint move with the seasons.
| Quote: |
Thanks for the great reply and encouragement, I appreciate it much!
Alex
|
Cheers,
Steve |
|
| Back to top |
|
|
mac davis
Guest
|
| Posted: Thu Oct 28, 2004 8:00 pm Post subject: Re: Wood sticks on my benchtop |
|
|
On Wed, 27 Oct 2004 11:44:26 -0400, "Zed Rafi" <zed@poloniese.com>
wrote:
you can also buy or make accessories, such as hold down clamps that
use the holes..
http://home.earthlink.net/~kvaughn65j/record_holdfast.jpg
(Ken Vaughn's site... an education in WW)
http://home.earthlink.net/~kvaughn65j/main.html
one of the most useful things that I've made are cam clamps...
I was trying to build glaceing clamps and wasn't happy with them... I
had cut out 2 or 3 cam-shaped pieces and put 3/4" dowels through them,
and one was laying on the bench... I found that I can use them as
"adjustable" pegs and clamp things in the middle of the bench with
them...
| Quote: |
Ahhhhhh...... i see.....
now that you've told me that, i see a million uses for it.... to think that
i've been clamping my workpieces down on my workbench all this time.... it
was annoying me so much and i kept thinking "there's gotta be another
way...."
thanks a lot for the info
"Stephen M" <smeier-spamless@primelink1.net> a écrit dans le message de
news:cloc1o0256r@news4.newsguy.com...
They are called "dog holes". The stick that you place in them is called a
"bench dog"
There should be a vise which also has one or more dog holes. A dog placed
in
a fixed hole in the bench top used in conjuction with a dog in the vise
become the "jaws" of potentially large vise or clamp above the surfadec
of
the bench.
You should be able to get the idea from the picture on this link
http://www.woodirect.com/workbench.htm
"Zed Rafi" <zed@poloniese.com> wrote in message
news:KSNfd.11295$Qs6.1128072@news20.bellglobal.com...
Hello,
A couple of years ago, i bought a workbench assembly at Canadian Tire
(our
Home Depot).
The top working surface has a number of holes bored through it, in each
of
which can be fitted the lower end of a cross-sectionally rectangular,
elongated wood stick. When this wood stick is fitted in one of these
bores,
it projects vertically upwardly from the surface of the workbench.
What are these for??? I imagine they're used as guiding means of some
sort.
I've kindda discarded them cause i didn't see any use for them.... but
i've
seen them around on other workbenches than mine, so i imagine they must
be
useful to some extent.
thanks for the info
|
|
|
| Back to top |
|
|
AAvK
Guest
|
| Posted: Thu Oct 28, 2004 9:41 pm Post subject: Re: Wood sticks on my benchtop |
|
|
| Quote: |
That sound Very cool to me. I like the idea of recycleing family furniture
I worthy cause.
DF = Doug Fir? Idunno'bout that. If I follow correctly, you would have 1"
"veneer" of maple over 2" of DF.
|
1" thick stock cut to 2" or 3" wide boards laminated as standing up, glued side
by side.
| Quote: |
That sounds like you are asking for a big
cup as the expansion and contraction rates differ.
90 degrees to the DF Like plywood on steroids? - Terrible idea . The
seasonal movement will split it it.
|
Understandable
| Quote: |
Here's what I would (and to some degree did):
1 - invest in Landis' "The Workbench Book", about $20 and really fun read.
|
I just might do that...
| Quote: |
2- Most of the beating, pounding and stress that wou will put on a bench for
hand work is within 6-8 inches of the front edge. Build up the beef in the
front where you need it.
|
It'll all be 3" thick as a whole top. I can't get too special here...
| Quote: |
3- Suppplement you stock with more maple. I purchased "brown maple". It's
maple, but with some heartwood. Same stuff, not as pretty, half the price.
|
I asked the exotic woods dealer, he said he's never tried to get it and never
heard of it, seems a shot futile. But there is a lot of wood in the table so a
little extra 5/4 maple wouldn't be too bad or too much, if needed.
| Quote: |
4 - Keep all the wood going left to right. If you do want bread-board ends
(going front to back) you can only lock the end at one point and let the
rest of the joint move with the seasons.
|
I'll have to learn about that joint thing, I'll buy that book.
| Quote: |
Cheers,
Steve
Then it would all have to be butcher-blocked, end to end. I wouldn't know how to |
arrange that unless I used an even-odd pattern like brick laying. That is because of
sizes of the pieces of wood in the table, I can't do an "all-like" gluing pattern that
will show weakness and be weaker like all the leaf pieces aligned up in the middle.
As far as strong seasonal differences in my town, hardly anything. The front door
gets a touch harder to close in rainy weather without any real water touching it
besides that which is in the air. Which is probably your very strong point of course...
duh! But the trestle will have to DF (previously, yes I had meant douglas fir, our
only local framing wood).
Alex |
|
| Back to top |
|
|
Prometheus
Guest
|
| Posted: Fri Oct 29, 2004 5:16 am Post subject: Re: Wood sticks on my benchtop |
|
|
On Wed, 27 Oct 2004 10:02:10 -0400, "Zed Rafi" <zed@poloniese.com>
wrote:
| Quote: |
Hello,
A couple of years ago, i bought a workbench assembly at Canadian Tire (our
Home Depot).
The top working surface has a number of holes bored through it, in each of
which can be fitted the lower end of a cross-sectionally rectangular,
elongated wood stick. When this wood stick is fitted in one of these bores,
it projects vertically upwardly from the surface of the workbench.
What are these for??? I imagine they're used as guiding means of some sort.
I've kindda discarded them cause i didn't see any use for them.... but i've
seen them around on other workbenches than mine, so i imagine they must be
useful to some extent.
thanks for the info
|
Not biting this one! |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in